Page 13 of 87 FirstFirst ... 3 11 12 13 14 15 23 63 ... LastLast
Threads 241 to 260 of 1724

Forum: Engineering and Design Main Forum

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 21,447
    petronextinternational
    11-15-2018, 12:07 AM Go to last post

  1. Deflection and Stress of arm with an angle

    Started by Enchantedhorses, 09-23-2019 10:33 AM
    • Replies: 1
    • Views: 3,725
    Cragyon
    09-23-2019, 08:42 PM Go to last post

  2. Tempered glass "burst" calculation

    Started by ezetom, 09-23-2019 09:54 AM
    • Replies: 0
    • Views: 3,297
    ezetom
    09-23-2019, 09:54 AM Go to last post

  3. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 10:48 AM
    • Replies: 4
    • Views: 4,828
    YorkshireDave
    09-22-2019, 10:49 AM Go to last post

  4. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 07:46 AM
    • Replies: 1
    • Views: 4,143
    Cragyon
    09-19-2019, 02:16 PM Go to last post

  5. Structural safe loading calculation

    Started by sdubey, 09-18-2019 09:36 PM
    • Replies: 1
    • Views: 4,302
    Cake of Doom
    09-19-2019, 04:13 AM Go to last post

  6. Physical height calculation of RA surface finishes.

    Started by billing, 09-16-2019 11:46 AM
    calculator, formula, ran, rms, surface finish
    • Replies: 1
    • Views: 4,236
    Kelly_Bramble
    09-16-2019, 02:29 PM Go to last post

  7. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 06:42 AM
    • Replies: 2
    • Views: 4,260
    lavdesesamajmeayakya
    09-05-2019, 02:18 PM Go to last post

  8. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 03:23 PM
    • Replies: 1
    • Views: 4,114
    JAlberts
    09-03-2019, 12:45 PM Go to last post

  9. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 09:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 4,306
    Kelly_Bramble
    08-30-2019, 10:21 AM Go to last post

  10. Angle Iron Stress

    Started by komet99, 04-03-2012 09:48 PM
    • Replies: 9
    • Views: 93,495
    administrator
    08-28-2019, 01:31 PM Go to last post

  11. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 03:14 PM
    • Replies: 1
    • Views: 4,415
    Kelly_Bramble
    08-23-2019, 08:27 AM Go to last post

  12. Uni project Help

    Started by Prialen08, 08-21-2019 09:41 AM
    design, jockey wheel
    • Replies: 0
    • Views: 4,179
    Prialen08
    08-21-2019, 09:41 AM Go to last post

  13. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 12:51 AM
    fabric, fashion, friction, material, science
    • Replies: 5
    • Views: 6,451
    bob_wolfe
    08-15-2019, 10:41 AM Go to last post

  14. Ways to lessen wear caused by a steel fixture

    Started by harrisonczaj, 07-15-2019 10:47 AM
    fixture design, part wear, plastic coating
    • Replies: 5
    • Views: 5,228
    bob_wolfe
    08-15-2019, 10:38 AM Go to last post

  15. SolidWorks Stress Analysis question

    Started by thinds, 08-12-2019 10:50 AM
    1 Attachment(s)
    • Replies: 2
    • Views: 3,730
    thinds
    08-13-2019, 08:10 AM Go to last post

  16. Material "Slash sheet description"

    Started by sdicarlo, 07-31-2019 02:41 PM
    • Replies: 0
    • Views: 3,334
    sdicarlo
    07-31-2019, 02:41 PM Go to last post

  17. Question tolerances, machining and cost

    Started by Ayien, 01-17-2018 07:23 PM
    gd&t, tolerances
    • Replies: 5
    • Views: 5,188
    jasonamurawski
    07-29-2019, 01:16 PM Go to last post

  18. Aluminum on plastic tolerance fit?

    Started by sebastian_thomas, 04-29-2018 02:05 PM
    • Replies: 1
    • Views: 3,797
    jasonamurawski
    07-29-2019, 01:10 PM Go to last post

  19. Need for advice

    Started by boutheynamzoughui, 07-29-2019 04:40 AM
    • Replies: 1
    • Views: 3,461
    Kelly_Bramble
    07-29-2019, 07:20 AM Go to last post

  20. Air tanks in parallel and series

    Started by rouncer81, 07-26-2019 05:04 PM
    • Replies: 2
    • Views: 4,600
    rouncer81
    07-26-2019, 05:38 PM Go to last post
Page 13 of 87 FirstFirst ... 3 11 12 13 14 15 23 63 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules