Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast
Threads 61 to 80 of 94

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. Astm b633

    Started by Dominguez Mexico, 03-21-2013 07:41 PM
    • Replies: 3
    • Views: 7,108
    PierArg
    03-27-2013, 09:00 AM Go to last post

  2. AN-40 Locknut Shaft Dimensions

    Started by bickeljm, 11-28-2012 12:00 PM
    • Replies: 1
    • Views: 7,594
    Kelly_Bramble
    11-28-2012, 05:42 PM Go to last post

  3. grip strut

    Started by Dominguez Mexico, 10-31-2012 11:34 AM
    • Replies: 3
    • Views: 6,123
    Dominguez Mexico
    11-27-2012, 04:58 PM Go to last post

  4. Looking for specs for NA standard (DoD metric) fasteners

    Started by yakman2020, 11-13-2012 11:21 AM
    • Replies: 2
    • Views: 8,645
    yakman2020
    11-13-2012, 12:00 PM Go to last post

  5. Self Tapping Screws Std. (18.6.4)

    Started by Francisco Michel, 11-05-2012 04:22 PM
    • Replies: 0
    • Views: 7,034
    Francisco Michel
    11-05-2012, 04:22 PM Go to last post

  6. 10-Degree Modified Square Thread

    Started by rafazoide, 08-22-2012 04:23 PM
    • Replies: 0
    • Views: 8,154
    rafazoide
    08-22-2012, 04:23 PM Go to last post

  7. design standard for centrifugal pumps

    Started by amuletm, 07-12-2012 04:04 AM
    • Replies: 1
    • Views: 5,999
    PinkertonD
    07-12-2012, 10:17 AM Go to last post

  8. EPM-001.12 Aerospace spec?

    Started by KELLY BURNS, 07-03-2012 02:34 PM
    • Replies: 2
    • Views: 7,000
    KELLY BURNS
    07-05-2012, 08:51 AM Go to last post

  9. ASCE7-05 Wind Load C&C

    Started by xezio, 06-20-2012 05:39 PM
    • Replies: 1
    • Views: 10,550
    Kelly_Bramble
    06-22-2012, 08:19 AM Go to last post

  10. Flow elements designation

    Started by aminaeen, 06-07-2012 11:18 AM
    • Replies: 0
    • Views: 5,380
    aminaeen
    06-07-2012, 11:18 AM Go to last post

  11. Washer standards

    Started by Dominguez Mexico, 03-12-2012 02:50 PM
    • Replies: 2
    • Views: 7,214
    Dominguez Mexico
    05-30-2012, 12:18 PM Go to last post

  12. Hardness norm & code

    Started by Dominguez Mexico, 05-30-2012 12:15 PM
    • Replies: 0
    • Views: 5,526
    Dominguez Mexico
    05-30-2012, 12:15 PM Go to last post

  13. ASTM Yield and Ulitimate Clarification

    Started by RWOLFEJR, 03-16-2012 11:11 AM
    • Replies: 2
    • Views: 11,756
    Kelly_Bramble
    03-18-2012, 09:32 AM Go to last post

  14. Drawing Standard Practices

    Started by Macguyver, 03-06-2012 04:58 PM
    • Replies: 2
    • Views: 9,689
    Kelly_Bramble
    03-07-2012, 08:21 AM Go to last post

  15. DIN Standard

    Started by jayman, 02-28-2012 08:20 PM
    din standards
    • Replies: 3
    • Views: 12,686
    RWOLFEJR
    02-29-2012, 02:05 PM Go to last post

  16. Red face LabVIEW users?

    Started by SmithDJ, 02-02-2012 06:24 AM
    labview, matlab, programmer
    • Replies: 0
    • Views: 5,901
    SmithDJ
    02-02-2012, 06:24 AM Go to last post

  17. required code in matlab

    Started by Karishma Dixit, 01-23-2012 02:45 AM
    • Replies: 0
    • Views: 5,515
    Karishma Dixit
    01-23-2012, 02:45 AM Go to last post

  18. Post Parts List Standard.

    Started by paddyh, 11-30-2011 05:11 AM
    • Replies: 2
    • Views: 11,579
    paddyh
    11-30-2011, 08:36 AM Go to last post

  19. Suitability of API 620/650 for low pressure tank at 316F

    Started by b8e, 11-04-2011 11:47 PM
    • Replies: 1
    • Views: 7,812
    Kelly_Bramble
    11-05-2011, 09:08 AM Go to last post

  20. Post RPR - Rupture pressure ratio

    Started by Warchief, 10-13-2011 04:06 PM
    • Replies: 0
    • Views: 8,836
    Warchief
    10-13-2011, 04:06 PM Go to last post
Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules