Page 9 of 31 FirstFirst ... 7 8 9 10 11 19 ... LastLast
Threads 161 to 180 of 603

Forum: Mechanical Engineering Forum

Mechanical Design, Mechanical Engineering and Design Engineering related forum topics.

  1. Looking for seamless forge rings

    Started by dennisjv123, 11-30-2018 05:27 AM
    • Replies: 1
    • Views: 2,778
    Kelly_Bramble
    11-30-2018, 07:19 AM Go to last post

  2. Time to heat up a certain volume of air in an enclosure

    Started by winghoe_tan, 10-02-2018 04:23 AM
    • Replies: 2
    • Views: 3,477
    sharvilohiya
    11-02-2018, 03:20 AM Go to last post

  3. Hydraulic Total Cost of Ownership

    Started by eugene_horak, 10-20-2018 04:52 PM
    hydraulics cost ownership
    • Replies: 2
    • Views: 3,116
    Hudson
    10-28-2018, 11:55 PM Go to last post

  4. Trench heating (copper to aluminium grill)

    Started by tobyemery1990, 10-10-2018 07:27 AM
    • Replies: 0
    • Views: 3,769
    tobyemery1990
    10-10-2018, 07:27 AM Go to last post

  5. newbie question: two pneumatic cylinders in series?

    Started by michael_baird, 09-27-2018 09:05 AM
    air cylinder in series 1 Attachment(s)
    • Replies: 6
    • Views: 5,802
    jboggs
    10-01-2018, 10:51 AM Go to last post

  6. Calculating torque of an L shaped lever

    Started by ross_46, 09-30-2018 01:55 AM
    • Replies: 1
    • Views: 3,415
    Kelly_Bramble
    09-30-2018, 06:18 AM Go to last post

  7. Could this clockwork compete other storage methods?

    Started by yahya_sharif, 09-28-2018 07:44 AM
    1 Attachment(s)
    • Replies: 0
    • Views: 2,825
    yahya_sharif
    09-28-2018, 07:44 AM Go to last post

  8. Timing pulley type selection for power transmission

    Started by futterama, 09-28-2018 03:33 AM
    • Replies: 0
    • Views: 2,925
    futterama
    09-28-2018, 03:33 AM Go to last post

  9. Controlling low air pressure

    Started by mike_landeros, 09-22-2018 10:46 PM
    • Replies: 2
    • Views: 2,951
    Hudson
    09-23-2018, 09:31 AM Go to last post

  10. Question Deck Joist Bending Calculations

    Started by exp741, 09-18-2018 11:11 AM
    2 Attachment(s)
    • Replies: 3
    • Views: 2,882
    Hudson
    09-19-2018, 09:46 PM Go to last post

  11. new style submarine/ pressure hull design

    Started by eddiewelch83, 09-03-2018 09:16 AM
    • Replies: 2
    • Views: 2,779
    Kelly_Bramble
    09-04-2018, 07:28 AM Go to last post

  12. Question Sensitive accurate material extraction tool for clay like material w/ thin sheathing

    Started by kde5fan, 08-27-2018 12:19 PM
    • Replies: 1
    • Views: 3,160
    JAlberts
    08-30-2018, 04:19 PM Go to last post

  13. Question Unexpectedly high normal stress -beam bending.

    Started by robert_cibula, 08-24-2018 03:14 PM
    euler-bernoulli theory, normal stress 4 Attachment(s)
    • Replies: 0
    • Views: 3,013
    robert_cibula
    08-24-2018, 03:14 PM Go to last post

  14. High Push / Pull Force 12 Volt Actuator

    Started by jasonroliver, 08-20-2018 12:29 PM
    • Replies: 1
    • Views: 3,007
    Kelly_Bramble
    08-20-2018, 12:52 PM Go to last post

  15. Lightbulb Career after BSME

    Started by nachaat25, 08-19-2018 10:04 PM
    • Replies: 1
    • Views: 3,308
    jboggs
    08-20-2018, 07:02 AM Go to last post

  16. Pressure testable burst disc....

    Started by ezetom, 08-04-2018 05:16 PM
    • Replies: 1
    • Views: 3,778
    JAlberts
    08-15-2018, 04:53 PM Go to last post

  17. Calculating required diameter of rod to support a given load

    Started by schembriandrew123, 08-14-2018 08:39 AM
    • Replies: 5
    • Views: 9,121
    Kelly_Bramble
    08-15-2018, 08:50 AM Go to last post

  18. Pump Inducer nomenclature

    Started by miladasiaban, 08-14-2018 03:28 AM
    cavitation, inducer, pump, turbomachinary 2 Attachment(s)
    • Replies: 0
    • Views: 3,282
    miladasiaban
    08-14-2018, 03:28 AM Go to last post

  19. Forces on bolt during vibration

    Started by winghoe_tan, 07-30-2018 02:22 AM
    1 Attachment(s)
    • Replies: 2
    • Views: 3,542
    winghoe_tan
    07-30-2018, 07:36 PM Go to last post

  20. Confused Centrifugal compressor Inspection

    Started by max_zhura, 05-15-2018 06:05 AM
    • Replies: 1
    • Views: 3,444
    ricardo_santos188
    07-22-2018, 03:54 PM Go to last post
Page 9 of 31 FirstFirst ... 7 8 9 10 11 19 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules